How to Repair Windows 7 System Files with System File Checker

How to Repair Windows 7 System Files with System File Checker

   Information

The sfc /scannow command (System File Checker) scans the integrity of all protected Windows 7 system files and replaces incorrect corrupted, changed/modified, or damaged versions with the correct versions if possible.

   Tip

If you get the Windows Resource Protection Could Not Start the Repair Service error when trying to run SFC, then make sure that the Windows Modules Installer service is enabled and set to Manual.

Services - Start or Disable

   Warning

Be aware that if you have modified your system files as in theming explorer/system files, running sfc /scannow will revert the system files such as explorer.exe back to it's default state. Make the appropriate backups of your system files that you have modified for theming if you wish to save them before running sfc /scannow.

 OPTION ONE 

To Run the SFC /SCANNOW Command at Boot

1. For how, see METHOD TWO at this link: SFC /SCANNOW : Run in Command Prompt at Boot

   Note

Using OPTION TWO below is recommended if able.

If you would like to get help with your SFC issue, then be sure to upload and attach your sfcdetails.txt file from OPTION THREE below in your post.

 OPTION TWO 

To Run the SFC /SCANNOW Command in Windows 7

1. Open an "elevated command prompt" (right click -> Run as administrator), and do step 2 or 3 below for what type of scan you would like to run.


2. To Scan and Repair System Files
NOTE: Scans the integrity of all protected system files and repairs the system files if needed. Please see red WARNING box at the top of this tutorial.

A) In the elevated command prompt, type sfc /scannow and press Enter. (see screenshot below)
NOTE: This may take a little bit to finish.

 

B) Go to step 4.

3. To Only Verify if the System Files are Corrupted
NOTE: Scans and only verifies the integrity of all proteced system files only. This command will not change your system files as in the red WARNING box at the top of this tutorial.

A) In the elevated command prompt, type sfc /verifyonly and press Enter.

4. When the scan is complete, hopefully you will see all is ok like the screenshot below.

   Note

• If SFC could not fix something, then run the command again to see if it may be able to the next time. Sometimes it may take running the sfc /scannow command 3 or more times to completely fix everything that it's able to.
• If not, then download and run the 32-bit (x86) or 64-bit (x64) System Update Readiness Tool for your same installed 32-bit or 64-bit Windows 7, restart the PC afterwards, and try the sfc /scannowcommand again.
• If still not, then try using OPTION ONE above to run the sfc /scannow command at boot.
• If still not, then you can attempt to run a System Restore using a restore point dated before the bad file occured to fix it. You may need to repeat doing a System Restore until you find a older restore point that may work.
• If still not, then you can use the steps in the TIP box in the OPTION THREE section below to manually replace the files that SFC could not fix if there are not to many fix.
• If there are to many files to manually fix, or you prefer not to use OPTION THREE below, then you could do a repair install without losing anything.

If you would like to get help with your SFC issue, then be sure to upload and attach your sfcdetails.txt file from OPTION THREE below in your post.

 

5. When done, close the elevated command prompt.

 OPTION THREE 

How to See and Read Only the "SFC" Scan Results from the CBS.LOG

   Note

When SFC runs, it logs it's actions into the C:\Windows\Logs\CBS\CBS.log. The steps in this option will show you how to see only the specific SFC entries with the [SR] tags in this CBS.log. This can be helpful to show you what files SFC could not fix automatically if you wanted to try and manually replace them.

1. Open an "elevated command prompt" (right click -> Run as administrator).

2. In the elevated command prompt, copy and paste the command below, and press Enter. (See screenshot below)
NOTE: This will place a sfcdetails.txt file on your desktop with only the SFC scan result details from the CBS.LOG in it.

Code:

findstr /c:"[SR]" %windir%\Logs\CBS\CBS.log >"%userprofile%\Desktop\sfcdetails.txt"

3. Close the elevated command prompt. 

4. Open the sfcdetails.txt file on your desktop to see the SFC scan details in the CBS.LOG. 

5. You can safely delete the sfcdetails.txt file afterwards if you like.

   Tip

If you need to replace a corrupted system file that SFC cannot fix, then this will show you how to by extracting a new copy directly from your Windows 7 installation DVD.

Extract Files from Windows 7 Installation DVD

That's it,
Shawn